Micom 3T Operations Instructions Page 131
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation
113
The radio is installed on the dashboard of the vehicle inside the passenger compartment. The other
components connect to the power source, the battery, and to the antenna, which enables the radio
to transmit and receive.
If the battery is located in the rear section of the vehicle, the power cable extends to the battery
location in the rear.
Note
To achieve maximum operating range, the antenna should be mounted as high on
the vehicle body as possible without striking overhead obstructions in the normal
service area of the vehicle. Select a mounting location on a flat portion of the
vehicle body, compatible with the maximum allowable high voltage lead-in cable
length.
MICOM-3F Installation
The procedure shown above for the MICOM-3R is also used to install the MICOM-3F.
MICOM-3T Installation
For MICOM-3T, only the control head, the speaker, and the microphone are installed in the
passenger compartment of the vehicle. The radio transceiver is installed in the trunk of the vehicle
together with the antenna tuner.
Figure 15 illustrates the installation procedure for the MICOM-3T.
Ferrite
Installation
Ferrite
Installation
Antenna
Connector
Antenna Cable
Power Cable
Control Head Cable
Control Head
Power
Connector
Transceiver
Trunk Compartment
Passenger Compartment
Outside the Car
Antenna
Green
Red
Black
Vehicle Frame
Ground
Engine
Compartment
+
-
12V
Batter
y
F2
7.5A
F1
30A
Microphone
Speaker
Speaker
Connector
Antenna
Tu ner
Figure 15. MICOM-3T Installation Diagram
- Owner’s Guide 1
- MICOM-3F/3T/3R 3
- HF-SSB Transceivers 3
- Table of Contents 5
- Acronyms 7
- Performance Specifications 11
- Warnings, Cautions and Notes 12
- General Safety Precautions 12
- Caution 13
- Facilities 16
- Vehicles 16
- Driver Safety 17
- Operational Warnings 17
- Intentionally Left Blank 18
- Transmitter Features 20
- Receiver Features 20
- Frequency Sources 20
- Power Source 21
- CW Keying Operation 21
- Programmable Features 21
- MICOM-3F Front Panel 22
- MICOM-3T Front Panel 23
- MICOM-3R Front Panel 24
- Rear Panel (All Models) 25
- LCD Display Functions 26
- RF Level Indications 27
- Audible Indications 27
- General Procedures 28
- Function Keys 29
- Scroll (MORE) Key 29
- Up/Down Scroll Keys 29
- Toggle Mode 29
- Alphanumeric Edit Mode 30
- Numeric Edit Mode 30
- View Mode 30
- Message Attached Alert 30
- (MICOM-3F/3R only) 31
- The Menu 32
- What you can Select 33
- Basic Operating Instructions 34
- Reflected 35
- Using the Channel Mode 36
- Channel Mode Options 37
- Choosing a New Channel 39
- Using the Frequency Mode 40
- 14,000.00 41
- F 15,000.00 41
- VFO Operation 43
- F 14,000.00 44
- F 15,_00.54 44
- Frequency Mode Options 45
- Storing Frequencies 47
- Using the Scan Mode 48
- Using the BIT Mode 49
- Locking the Radio 50
- Changing the Password 51
- Scanning 52
- Sounding 52
- Sounding Cycle Time 53
- LQA Memory 54
- Bidirectional Handshake 54
- Selective Calling 55
- ALE Addressing Method 55
- Address and Call Types 55
- Group Addresses 57
- AllCall Addresses 58
- AnyCalls 58
- Using the MultiNet Feature 59
- Messages 60
- Using the Caller Stack 60
- Quick Call 60
- Entering the ALE Mode 61
- ALE Mode Options 62
- Receiving Calls in ALE Mode 63
- ➤ Receiving a net call: 64
- ➤ Receiving an AllCall: 64
- ➤ Receiving an AnyCall: 64
- Link State 66
- Disconnecting Calls 71
- CH 3 30% 74
- Using Autodial 76
- Sending Messages 77
- Other Types of Calls 79
- Transmitting AIICalls 80
- Transmitting Net Calls 83
- Transmitting Group Calls 84
- END CALLING 85
- Transmitting AnyCalls 86
- ➤ To transmit an AnyCall: 87
- Transmitting Wildcard Calls 89
- Transmitting a Self Call 91
- Using the Inlink Function 95
- Using the Programming Mode 96
- Programming Channels 100
- Selecting Radio Parameters 102
- Setting Radio Options 104
- ALE Programming 105
- Programming Nets 106
- Default Values 107
- Setting the Net Options 108
- Directory Parameters 108
- AMD Message Configuration 109
- ALE Options Configuration 109
- Auto Dial Parameters 111
- Storing ALE parameters 111
- PROGRAMMING 112
- Introduction 113
- Using the VP-116 Unit 114
- Using the Vocoder 118
- Programming the Vocoder 120
- Erasing the Stored Keys 121
- GPS Receiver Functions 122
- GPS Antenna 123
- Operating the GPS Receiver 124
- First-Time Operation 125
- Operating Instructions 126
- What to do if … 127
- Installation 128
- Green (Output 1 - max. 5A) 129
- Black (Ground) 129
- Red (Output 2 - max. 25A) 129
- 5A GND 25A 129
- 5A - 25A 129
- MICOM-3R Installation 130
- MICOM-3F Installation 131
- MICOM-3T Installation 131
- Installation Procedures 133
- Throughly 134
- Clean this Area 134
- Floor Surface 134
- Microphone Clip 135
- Important 136
- MICOM-3T Final Connections 137
- Operational Checks 137
- Connectors 138
- Antenna Connector J2 139
- Accessories Connector J5 139
- DC Power Connector 141
- Vehicular Noise Reduction 141
- Maintenance 142
- Using BIT 143
- Troubleshooting 145
- Service 147
- Appendix A 148
- 3 5-50 Watt HF-SSB 148
- Backpack Transceiver 148
- Purpose and Use 149
- Equipment Description 149
- Unpacking and Inspection 152
- Backpack Carrying Harness 153
- Warning 155
- Installation of Whip Antenna 157
- List of Procedures 162
© 2020, manymanuals.com. All rights reserved. | 0.949 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals