Micom 3T Operations Instructions Page 95
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Using Automatic Link Establishment (ALE)
77
Using the Inlink Function
When the inlink function is enabled (see instructions in the ALE Options
Configuration section starting on page 91), the stations participating in a
call are automatically notified by a DISC message whenever another
participant leaves (disconnects from) the call.
MICOM-3
PAGE
LQA
MON
DISC
1001
USB
The link is then automatically disconnected when only one station is left (that is, after all the other
participants disconnected).
The inlink function is available in any type of call that involves the setting up of a link using
bidirectional handshaking. Therefore, you can use it in individual calls, group calls, net calls, etc., but
not in AllCalls and self calls.
Notes
For the inlink function to operate correctly, it must be enabled on all the stations.
Do not enable the inlink function when communicating with a radio that does not
support the full ALE capabilities in accordance with MIL-STD-188-141B.
To avoid disconnecting the link too soon as a result of inactivity (that is,
after the PTT time-out interval (PTOT) programmed under the ALE Options
Configuration section), each participant can request other stations to wait
beyond the PTOT interval (up to 10 minutes more) before automatic
disconnection occurs.
MICOM-3
RCLV
FREQ
TOT
LINK
1001
USB
This option (TOT – time-out interval) is displayed over the F4 key after the link is set up: to send a
request for the other stations to wait more time, press the TOT (F4) key.
Transmitting ALE Calls in the Channel Mode
The ALE option is available in both the ALE and Channel modes and therefore, the radio can also
answer ALE calls.
The transmission process is similar for both operating modes, with the following differences:
• In the Channel mode, every call is initiated on the currently selected channel.
• The LQA function is not available in the Channel mode: sounding and bidirectional calls can
only be initiated in the ALE mode.
• When the radio is in the Channel mode, it uses the parameters programmed for net 1.
Important
If net 1 is not programmed, there is no ALE functionality in the Channel
mode, even if the ALE option is turned on.
- Owner’s Guide 1
- MICOM-3F/3T/3R 3
- HF-SSB Transceivers 3
- Table of Contents 5
- Acronyms 7
- Performance Specifications 11
- Warnings, Cautions and Notes 12
- General Safety Precautions 12
- Caution 13
- Facilities 16
- Vehicles 16
- Driver Safety 17
- Operational Warnings 17
- Intentionally Left Blank 18
- Transmitter Features 20
- Receiver Features 20
- Frequency Sources 20
- Power Source 21
- CW Keying Operation 21
- Programmable Features 21
- MICOM-3F Front Panel 22
- MICOM-3T Front Panel 23
- MICOM-3R Front Panel 24
- Rear Panel (All Models) 25
- LCD Display Functions 26
- RF Level Indications 27
- Audible Indications 27
- General Procedures 28
- Function Keys 29
- Scroll (MORE) Key 29
- Up/Down Scroll Keys 29
- Toggle Mode 29
- Alphanumeric Edit Mode 30
- Numeric Edit Mode 30
- View Mode 30
- Message Attached Alert 30
- (MICOM-3F/3R only) 31
- The Menu 32
- What you can Select 33
- Basic Operating Instructions 34
- Reflected 35
- Using the Channel Mode 36
- Channel Mode Options 37
- Choosing a New Channel 39
- Using the Frequency Mode 40
- 14,000.00 41
- F 15,000.00 41
- VFO Operation 43
- F 14,000.00 44
- F 15,_00.54 44
- Frequency Mode Options 45
- Storing Frequencies 47
- Using the Scan Mode 48
- Using the BIT Mode 49
- Locking the Radio 50
- Changing the Password 51
- Scanning 52
- Sounding 52
- Sounding Cycle Time 53
- LQA Memory 54
- Bidirectional Handshake 54
- Selective Calling 55
- ALE Addressing Method 55
- Address and Call Types 55
- Group Addresses 57
- AllCall Addresses 58
- AnyCalls 58
- Using the MultiNet Feature 59
- Messages 60
- Using the Caller Stack 60
- Quick Call 60
- Entering the ALE Mode 61
- ALE Mode Options 62
- Receiving Calls in ALE Mode 63
- ➤ Receiving a net call: 64
- ➤ Receiving an AllCall: 64
- ➤ Receiving an AnyCall: 64
- Link State 66
- Disconnecting Calls 71
- CH 3 30% 74
- Using Autodial 76
- Sending Messages 77
- Other Types of Calls 79
- Transmitting AIICalls 80
- Transmitting Net Calls 83
- Transmitting Group Calls 84
- END CALLING 85
- Transmitting AnyCalls 86
- ➤ To transmit an AnyCall: 87
- Transmitting Wildcard Calls 89
- Transmitting a Self Call 91
- Using the Inlink Function 95
- Using the Programming Mode 96
- Programming Channels 100
- Selecting Radio Parameters 102
- Setting Radio Options 104
- ALE Programming 105
- Programming Nets 106
- Default Values 107
- Setting the Net Options 108
- Directory Parameters 108
- AMD Message Configuration 109
- ALE Options Configuration 109
- Auto Dial Parameters 111
- Storing ALE parameters 111
- PROGRAMMING 112
- Introduction 113
- Using the VP-116 Unit 114
- Using the Vocoder 118
- Programming the Vocoder 120
- Erasing the Stored Keys 121
- GPS Receiver Functions 122
- GPS Antenna 123
- Operating the GPS Receiver 124
- First-Time Operation 125
- Operating Instructions 126
- What to do if … 127
- Installation 128
- Green (Output 1 - max. 5A) 129
- Black (Ground) 129
- Red (Output 2 - max. 25A) 129
- 5A GND 25A 129
- 5A - 25A 129
- MICOM-3R Installation 130
- MICOM-3F Installation 131
- MICOM-3T Installation 131
- Installation Procedures 133
- Throughly 134
- Clean this Area 134
- Floor Surface 134
- Microphone Clip 135
- Important 136
- MICOM-3T Final Connections 137
- Operational Checks 137
- Connectors 138
- Antenna Connector J2 139
- Accessories Connector J5 139
- DC Power Connector 141
- Vehicular Noise Reduction 141
- Maintenance 142
- Using BIT 143
- Troubleshooting 145
- Service 147
- Appendix A 148
- 3 5-50 Watt HF-SSB 148
- Backpack Transceiver 148
- Purpose and Use 149
- Equipment Description 149
- Unpacking and Inspection 152
- Backpack Carrying Harness 153
- Warning 155
- Installation of Whip Antenna 157
- List of Procedures 162
© 2020, manymanuals.com. All rights reserved. | 1.894 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals